News details
Nylon Engineering Plastic PA6-A640GA for Demanding Parts
Release time:
2026-11-06
The Nylon engineering plastic PA6-A640GA from Anhui Jinxi New Materials Technology Co., Ltd. is a modified nylon PA6 with 40 percent glass fiber. The product page describes it as having an excellent surface appearance and processability, outstanding resistance to thermal aging, self-lubricating properties, superior mechanical performance and exceptional high-temperature and corrosion resistance. Jinxi supplies modified PPS, LCP, PA6, PA66, HTPA and nylon microspheres.
Grade and Properties
The A640GA grade is listed in the PA6+40GF column. The density is 1.45 grams per cubic centimeter under ISO 1183. The mold shrinkage is 0.2 percent in the parallel direction and 0.45 percent in the vertical direction under ISO 294. The tensile breaking strength is 200 megapascals under ISO 527 with a type I sample at 50 millimeters per minute.
The flexural strength is 300 megapascals at 23 degrees Celsius and 2 millimeters per minute under ISO 178, and the flexural modulus is 11000 megapascals under the same standard. The notched Izod impact strength is 15 kilojoules per square meter at 23 degrees Celsius under ISO 180, and the unnotched Charpy impact strength is 90 kilojoules per square meter at 23 degrees Celsius under ISO 179. The melting point is 220 degrees Celsius under ISO 11357-1.
The page also lists the heat deflection temperature and other grades in the same table. The buyer should request the full data sheet for the A640GA grade, including the heat deflection temperature, the flammability rating and the electrical properties, because the extracted page only shows part of the table.
Processing
A 40 percent glass fiber PA6 is a stiff material, so the injection molding conditions should be set for the higher melt viscosity and the fiber orientation. The buyer should confirm the recommended melt temperature, the mold temperature, the injection speed and the drying condition. A material that is not dried properly can show silver streaks or a loss of mechanical properties.
The mold shrinkage differs between the parallel and vertical directions, which means the part can warp if the gate and the cooling are not balanced. The buyer should discuss the gate location and the cooling layout with the molder. A flat part with a long flow path may need a different shrinkage allowance from a small, thick part.
The product page says the material has good surface appearance and processability. The buyer should confirm the surface requirement and the color on a sample. A glass fiber grade can show fiber read-through on a glossy surface, so the mold finish and the gate position matter.

Applications
Jinxi lists aerospace, auto parts, electrical and electronic, medical devices, industrial manufacturing and household appliances as application areas. The A640GA grade can be considered for a structural part that needs stiffness, heat resistance and dimensional stability. The buyer should confirm the load, the temperature and the chemical exposure before choosing the grade.
For an auto part, the buyer should check the temperature cycle, the vibration and the fluid contact. For an electrical part, the buyer should check the electrical properties and the flammability rating. For an industrial part, the buyer should check the wear and the corrosion resistance. A data sheet value is a starting point, not a substitute for a part test.
The product page offers customized solutions. The buyer should send the drawing, the application and the test requirement so that the supplier can recommend the grade or a modification. A color match and a flame retardant grade may need a different formulation.
Ordering Notes
The order should state the grade, the glass fiber content, the color, the packaging, the quantity and the test report required. The buyer should also confirm the lead time, the minimum order quantity and the batch consistency.
A sample is the practical way to check the pellets, the drying behavior and the molded part. The buyer should run a trial mold and test the part before the bulk order. The trial record should be kept as the reference for the production batch.
Jinxi can be contacted through the details on the product page. The buyer should send the part drawing and the performance requirement so that the supplier can recommend the grade.
The Nylon engineering plastic is one material in a molded part, and the result depends on the grade, the mold, the process and the part design. A clear specification and a trial mold reduce the risk of a material that does not meet the part requirement.
Relevant information
Future Trends: PA66 Glass Fiber Reinforced Electrical Grade in Sustainable Buildings
Future Trends: PA66 Glass Fiber Reinforced Electrical Grade in Sustainable Buildings Table of Contents 1. Introduction to Sustainable Building Materials 2. What is PA66 Glass Fiber Reinforced Electrical Grade? 3. Advantages of PA66 in Construction 4. Applications of PA66 in Sustainable Buildings 5. Environmental Impact of Using PA66 6. Future Trends in PA66 Usage 7. Ch
Learn more