News details


Unfilled PPS vs Glass Fiber Reinforced PPS Key Differences

Image Source: statics.mylandingpages.co Unfilled PPS wins on toughness, surface smoothness, and cost. Glass fiber reinforced PPS wins on stiffness, heat resistance, and dimensional stability. Glass fiber reinforced PPS plastic typically lifts tensile strength from roughly 70–120 MPa to 120–200 MPa or more, according to PatSnap data. The righ

Release time:

2026-11-06

Unfilled
Image Source: statics.mylandingpages.co

Unfilled PPS wins on toughness, surface smoothness, and cost. Glass fiber reinforced PPS wins on stiffness, heat resistance, and dimensional stability. Glass fiber reinforced PPS plastic typically lifts tensile strength from roughly 70–120 MPa to 120–200 MPa or more, according to PatSnap data. The right choice matches the grade to the part's dominant demand: impact tolerance and finish, or mechanical strength and thermal stability.

Unfilled PPS owns better toughness and sliding performance but weak rigidity and poor high-temperature dimensional stability. Glass fiber reinforced PPS gains greatly improved strength, heat resistance and anti-warpage at the cost of reduced impact ductility.

Key Takeaways

  • Glass fiber reinforced PPS is much stiffer and handles higher heat than unfilled PPS.
  • Unfilled PPS is tougher and has a smoother surface than glass fiber reinforced PPS.
  • Choose the PPS grade that best matches your part's main need: strength and heat, or impact resistance and finish.

Mechanical Rigidity and Strength

Mechanical
Image Source: unsplash

Stiffness and Tensile Strength

Stiffness separates these grades more than any other property. The unfilled polymer shows a Young's modulus of 2.60–4.20 GPa and a flexural modulus of 2.3–3.9 GPa, according to Aon3D. Glass fiber can increase flexure modulus up to 14 GPa in glass fiber reinforced composite versions. A comparison from plastic-material.com makes the gap clear:

PropertyNeatGF40
Flexural modulus3.9 GPa10.5 GPa

The glass fiber (GF) filler carries load and restricts chain movement. This mechanism delivers enhanced flexural modulus and higher tensile strength. The unfilled grade typically reaches 70–120 MPa. Glass fiber reinforced PPS plastic pushes past 120–200 MPa. Engineers who compare pps material properties across grades see the same pattern in tensile & flexural modulus data. These mechanical properties define mechanical rigidity, and rigidity drives the grade choice here.

Glass fiber lifts stiffness and HDT dramatically but adds brittleness and does not raise the 90°C glass transition.

Creep Resistance Under Load

Creep resistance follows the same logic. Unfilled pure PPS sheet deforms slowly under sustained stress, especially in warm conditions. The glass fiber reinforced pps sheet resists this drift far better. Rigid fibers share the load and block chain slippage. A gf-filled pps part therefore holds its shape for years in bolted joints and springs. Glass-fiber reinforcement also improves mechanical properties under continuous load. A glass filled pps sheet and other reinforced pps formats trade ductility for this stability.

High-Temperature Performance

Heat Deflection Temperature

Heat deflection temperature (HDT) shows the sharpest split between these two grades. PatSnap reports the hdt of pps at 135°C for unfilled PPS at 1.82 MPa. A glass fiber reinforced pps plastic with 30% glass fiber reaches 260°C under the same load.

MaterialHeat Deflection Temperature (HDT)
Unfilled PPS135°C at 1.82 MPa
PPS with 30% glass fiber reinforcement260°C

That enhanced hdt changes design limits. A glass fiber reinforced pps sheet holds stiffness near its melting range. An unfilled pure pps sheet softens much earlier under load. Engineers gain roughly 125°C of headroom from the fiber addition.

Long-Term Thermal Aging

Long-term aging tests reveal how each grade keeps its mechanical properties after weeks at elevated heat. The reinforced grade retains strength far longer. Glass fibers block chain scission and slow property loss. Oxidation at the surface drives most of the loss. Fiber loading reduces oxygen access and limits crack growth. The unfilled grade still offers solid high-temperature resistance for moderate service. A glass filled pps sheet suits continuous heat near 200°C or above. An unfilled pps part works well in lower thermal bands. Both grades resist thermal degradation. The choice depends on the peak temperature and the load the part carries. Designers should test the actual part in its service environment before final grade approval.

Dimensional Stability

Shrinkage and Warpage

Shrinkage behavior differs sharply between the two grades. Unfilled PPS shows high mold shrinkage and uneven contraction across thick and thin walls. The unfilled pure pps sheet therefore tends to warp after molding or machining. Glass fibers restrict resin movement during cooling. A glass fiber reinforced pps sheet shrinks far less and holds flatness across large parts. The reinforced grade delivers enhanced dimensional stability for tight-tolerance components. A glass filled pps sheet also resists post-mold distortion in long, thin geometries.

Coefficient of Thermal Expansion

Thermal expansion data confirms the same pattern. The neat resin expands more with heat. Glass fiber reinforced pps plastic cuts the coefficient of thermal expansion (CTE) by roughly half or more, depending on fiber loading.

MaterialCTE (flow direction)
Unfilled PPS~5–7 × 10⁻⁵ /°C
GF40~2–3 × 10⁻⁵ /°C

Lower CTE protects mechanical properties in assemblies with metal inserts. Metal-to-plastic joints benefit most from the lower value. This sheet keeps clearances stable across temperature swings. An unfilled pps part may bind or loosen as it expands. Designers who specify the material for precision housings should weigh this factor early. The unfilled grade still suits parts with generous tolerances and low thermal cycling.

Impact and Sliding Behavior

Notched Impact Toughness

Impact toughness favors the neat grade. Glass fibers add stiffness, yet they also create stress concentrations that crack under sudden loads. Ensinger Plastics notes that unfilled PPS reaches a notched Charpy value of 2.6 kJ/m², while a tougher polymer such as PEEK reaches 4 kJ/m². Toray data shows the same split across its Torelina line. Unreinforced grades A900 and A670T05 reach 4.0 and 5.8 kJ/m². Glass fiber reinforced grades climb to 11.0–12.0 kJ/m² in notched Charpy terms, yet these figures reflect fiber bridging rather than ductile yielding.

GradeTypeNotched Charpy impact strength (kJ/m2)
A504X90Glass fiber reinforced11.0
A604Glass fiber reinforced12.0
A310MX04Glass + filler reinforced8.0
A610MX03Glass + filler reinforced7.0
A673MElastomer improvement15.0
A575W20Elastomer improvement7.3
A495MA2Elastomer improvement7.5
A900Unreinforced4.0
A670T05Unreinforced5.8

Toray plots these grades side by side in a bar chart of notched Charpy impact strength.

Bar
Image Source: statics.mylandingpages.co

An unfilled pure pps sheet absorbs shock without shattering. A glass fiber reinforced pps sheet resists a sharp blow less well. Designers who need drop resistance should favor the unfilled grade.

Friction and Wear Performance

Sliding behavior also favors the unfilled grade. Neat PPS offers a low friction coefficient and smooth wear against metal. Glass fibers raise hardness and cut abrasive wear in some setups. The fibers can also scratch a mating surface and raise friction. A glass fiber reinforced pps sheet suits high-load bearings with hard counterfaces. An unfilled pps part suits low-load slides and quiet running. Both grades keep useful mechanical properties in sliding contact. The application load decides the better fit.

Surface Finish and Machining

Surface Smoothness and Appearance

Surface quality depends heavily on resin flow and gas release during molding. PatSnap reports that gas evolution from sizing agents drives roughness in compression-molded parts. Lower processing temperatures reduce gas generation and deliver smoother finishes. The data below shows the effect of molding temperature on surface roughness.

ConditionSurface Roughness (Ra)
Molding temperature 300°C3.5–5.0 μm
Molding temperature 270°C1.2–2.0 μm

An unfilled pure pps sheet molds to a glossy, uniform surface with minimal fiber read-through. A glass fiber reinforced pps sheet shows fiber texture at the surface and often needs painting or coating for cosmetic parts. Appearance-critical housings favor the neat grade.

Machining and Tool Wear

Tool wear separates the two grades during secondary operations. Cylex Plastics rates glass-filled stock as abrasive and demanding polycrystalline diamond tooling.

Machinability & Tool Wear Index: Unfilled PPS — Easy (Standard Carbide); Glass-filled PPS — Severe Wear (Carbide/PCD).

Tops Plastics confirms this split. Glass reinforcement increases cutting-edge wear, so a glass fiber reinforced pps sheet needs reinforced-polymer tooling and wear monitoring. An unfilled pps grade machines with standard carbide and holds a simpler tool-life profile. Operators should track critical dimensions and surface trends on pps parts rather than assume a fixed replacement interval. Both grades retain their mechanical properties after machining when cutters stay sharp and feeds stay moderate.

Density and Part Weight

Glass Fiber Reinforced PPS Sheet Density

Glass fiber loading raises density in a predictable way. Unfilled PPS sits near 1.35 g/cm³. A glass fiber reinforced pps sheet with 40% glass content climbs to roughly 1.65–1.70 g/cm³. The table below shows typical values across common grades.

MaterialDensity (g/cm³)
Unfilled PPS~1.35
PPS + 30% glass fiber~1.55
PPS + 40% glass fiber~1.65–1.70

The glass fiber reinforced pps plastic carries more mass per unit volume. A glass fiber filled pps board weighs about 20–25% more than the same part in neat resin. Designers should factor this gain into weight budgets early.

Weight Impact on Part Design

Extra density changes part design in practical ways. A heavier pps component shifts the center of gravity and loads mounting points harder. Thinner walls can offset the gain, yet stiffness must stay intact. The reinforced grade keeps mechanical properties high at reduced wall thickness. An unfilled pps part offers lighter weight with lower rigidity. Aerospace and handheld devices often favor the lighter grade. Structural brackets and pump housings accept the extra mass for added strength. Teams should weigh density against stiffness targets before locking the design.

Raw Material Cost

Price per Kilogram Comparison

Cost often decides the grade before any test begins. Unfilled PPS carries a higher sticker price than the glass-filled version. Plasticmoulds.net lists GF40 PPS at $25–30/kg across North America and Europe as of Q2 2026. The same source reports unfilled PPS at about $5/kg more than GF40.

GradePrice
GF40 PPS list price (North America and Europe, as of Q2 2026)$25–30/kg
Unfilled PPSabout $5/kg more than GF40

The glass fiber reinforced pps sheet costs less per kilogram because glass fiber replaces expensive resin volume. Buyers who compare quotes often assume the neat grade saves money. The data shows the opposite at the resin level.

Cost-to-Performance Balance

Price per kilogram tells only half the story. A part made from an unfilled pure pps sheet needs more wall thickness to reach a stiffness target. That extra volume erodes the resin savings. The glass-filled grade reaches the same rigidity with less material, so cost per part can favor either option. Teams should weigh pps density, cycle time, and scrap rate alongside the raw price. The unfilled grade still wins on total cost for thin-wall, cosmetic, or impact-critical parts. Glass-filled pps earns its place when stiffness and heat resistance drive the design. A fair comparison tracks cost per finished part, not cost per bag. Both grades protect their mechanical properties over time, so the decision rests on the dominant demand of the application.

Ideal Usage Scenarios

Where Unfilled Pure PPS Sheet Fits Best

The unfilled grade shines in applications where impact tolerance, surface quality, and cost control drive the design. Parts that face sudden drops or shock loads benefit from the ductile nature of the neat resin. A housing for a handheld diagnostic tool, for example, must survive a fall onto a hard floor without cracking. The unfilled pure pps sheet absorbs that energy and keeps the enclosure intact. Cosmetic components also favor this grade. A visible front panel or a display bezel needs a smooth, uniform surface with no fiber texture showing through. The neat resin delivers a glossy finish straight from the mold, so painting or coating becomes optional rather than mandatory.

Chemical processing equipment often uses this grade for pump components and valve bodies that contact aggressive fluids. The unfilled polyphenylene sulfide sheet resists a wide range of solvents and acids without the fiber network that can wick chemicals along the interface. Low-load sliding parts, such as quiet-running gears and bushings in consumer appliances, also suit the neat grade. These parts need low friction and smooth operation rather than high stiffness. Thin-wall, lightweight components in portable electronics represent another strong fit. The lower density of the unfilled resin keeps part weight down, and the material's toughness protects delicate internal structures. Designers who prioritize impact resistance and appearance over raw strength should start their evaluation with this grade.

Where Glass Filled PPS Sheet Fits Best

The reinforced grade takes over when stiffness, heat resistance, and dimensional control dominate the requirements. Structural brackets and mounting plates that carry continuous loads need the higher flexural modulus of the glass fiber reinforced pps sheet. Underhood automotive components, such as sensor housings and connector bodies, face temperatures that would soften the neat resin. A standard glass filled pps sheet holds its shape at those temperatures and keeps critical dimensions stable. Precision parts in pumps and valves also favor the reinforced grade. These components must maintain tight clearances across thermal cycles, and the low coefficient of thermal expansion of the filled material protects those tolerances.

Electrical and electronic applications represent another core fit. Connectors, bobbins, and switch housings need both heat resistance and dimensional stability, and a glass filled pps sheet delivers both. The gf-filled pps grade also suits high-load bearings and wear parts with hard metal counterfaces. The glass fibers raise hardness and reduce abrasive wear in these demanding contact situations. Large, flat parts that must stay flat after molding, such as structural panels and support plates, benefit from the reduced warpage of the reinforced grade. Teams that need the mechanical properties of a metal replacement in a polymer part should evaluate the glass-filled option first. The added stiffness and thermal headroom often justify the trade-offs in impact ductility and surface finish.

Step-by-Step Selection Guide

A structured evaluation removes guesswork from the grade decision. The four checks below move from the most demanding requirement to the least, so a single failing criterion can settle the choice early. Each step pairs a service condition with the grade that handles it best.

Working Temperature Check

Temperature sets the first filter. The unfilled grade softens under load at 135°C, while a 30% glass fiber compound holds its shape to 260°C at 1.82 MPa. A part that sees continuous service above 150°C under load needs the reinforced option. A part that stays below 120°C can use either grade, and the remaining checks decide the matter.

Designers should measure the peak temperature at the part surface, not the ambient air in the enclosure. Local hot spots near motors, connectors, or power components often run 20–30°C above the surrounding air. A short thermal soak test on a prototype reveals these zones before the material locks in. Parts that face repeated soldering, reflow, or autoclave cycles also belong in the high-heat category. The glass fiber reinforced pps sheet absorbs that thermal load without creeping. Moderate-temperature parts with generous safety margins leave room for the neat grade.

Load-Bearing Requirements

The second check examines the load the part carries and how long it carries it. A bracket that supports a static load for years needs creep resistance, and the glass-filled grade wins that contest. A cover or a cosmetic panel that carries little stress does not need fiber reinforcement. Designers should calculate the actual stress at the highest service temperature, not at room temperature. The allowable stress drops as temperature rises, and the gap between grades widens at the top of the range.

Deflection limits matter as much as strength. A structural part that must hold a flat surface or a precise gap needs the higher flexural modulus of the reinforced grade. A part that flexes during assembly or absorbs a snap-fit needs the ductility of the neat resin. Teams should list every load case, including assembly force, transport shock, and misuse. A part that passes the static load test but cracks during a drop belongs in the unfilled category. A part that sags after months under a bolted joint belongs in the reinforced category.

Friction and Wear Needs

The third check looks at sliding contact. The neat resin offers a low friction coefficient and quiet running against metal. The glass-filled grade raises hardness and resists abrasive wear, yet the fibers can scratch a soft mating surface. Designers should identify the counterface material and its hardness before choosing. A hard steel shaft tolerates glass fibers well. A soft aluminum or brass surface may wear faster against the filled grade.

Load and speed complete the picture. High-load bearings with hard counterfaces favor the reinforced compound. Low-load slides, gears in consumer appliances, and quiet-running bushings favor the neat resin. Lubrication changes the answer as well. A lubricated joint reduces the wear penalty for either grade. A dry-running joint amplifies the difference. Teams should test the actual pair in a wear rig when the application is critical. Published friction data offers a starting point, not a final answer.

Budget Considerations

The fourth check weighs cost per finished part, not cost per kilogram. The raw numbers favor the filled compound at the resin level, yet tooling and cycle time shift the balance. The plasticmoulds.net cost breakdown lists the hidden factors:

  • Glass-filled PPS compounds generally range from $5–$15 per kilogram depending on grade, filler content, supplier region, and order volume.
  • PPS molds require hardened, corrosion-resistant steels (H13, S136 at 48+ HRC) and high-temperature-capable cooling systems; these requirements can increase upfront tooling investment by 15–30% compared to molds for commodity plastics.
  • PPS cooling runs 25–35 seconds for a 2 mm wall versus 8–12 seconds for ABS, so machine hours per thousand parts are meaningfully higher; factor this into volume pricing rather than comparing material cost alone.
  • Higher material cost than commodity and standard engineering plastics like nylon and PBT. Brittleness in unfilled grades limits use without glass fiber or mineral reinforcement.

The relative cost ladder puts these figures in context, according to Quanda Plastic:

MaterialRelative Material Cost
Unfilled Base PlasticStandard ($)
Glass-Filled Plastic (30% GF)Cost-Effective ($$)
Carbon-Fiber-Reinforced Plastic (30% CF)Premium ($$$)

Material yield calculations must account for the high cost of this PPS engineering plastic; selecting a profile closest to the final part dimensions minimizes waste and tooling costs, as Jutai Plastics notes. A near-net-shape sheet or rod cuts scrap and machining time, and that saving often outweighs a small difference in resin price.

The grade decision itself follows a simple rule from GBM Injection:

Recommendation: Choose unfilled PPS for chemical resistance and flow-sensitive precision components. Choose glass filled PPS for higher stiffness and structural performance.

Quanda Plastic adds a matching guideline for the reinforced side:

Select Glass-Filled Plastics when: You need high structural rigidity, high creep resistance, and elevated HDT at a reasonable material cost.

Teams should build a cost model that includes resin, tooling amortization, cycle time, scrap rate, and secondary operations. The model should run at the expected annual volume, not at a single unit. A low-volume program may never recover the higher tooling cost of the filled grade. A high-volume program spreads that cost across thousands of parts and often favors the reinforced compound. The unfilled grade keeps its edge in thin-wall, cosmetic, and impact-critical parts where the filled grade needs extra wall thickness or added processing steps. Both grades reward an early cost review, before the design freezes the wall sections and the tool layout.

Comparison with Pure PPS: Quick Reference

Property-by-Property Summary

A side-by-side comparison with pure PPS clarifies where each grade earns its place. Plasticmoulds.net summarizes the key differences in a single reference table.

PropertyUnfilled PPSGlass Fiber Reinforced PPS
Shrinkage0.6–1.4% in both directions (isotropic)Anisotropic: 0.3–0.5% flow direction, 0.8–1.2% transverse
Brittleness / toughnessMore brittle; unmodified PPS is brittleGlass gives enough toughness for press-fit assembly
Thermal / mechanical—Glass roughly doubles HDT; triples flexural modulus; default is 40% glass fiber
Processing / moldingMold at lower end of ranges; back pressure of 5–10 MPaGF grades run at top of both ranges
Application suitabilityChemical-handling parts, electrical insulators, capacitor housingsFixes mechanical and thermal problems; over 80% of molded PPS is reinforced

The table shows the trade-offs clearly. The neat grade keeps isotropic shrinkage and suits chemical or electrical parts. A glass fiber reinforced pps sheet fixes mechanical and thermal limits, yet it warps more easily because of anisotropic shrinkage. The flexural modulus triples with glass loading, and heat deflection temperature roughly doubles. These pps material properties guide the final choice. Over 80% of molded PPS in the market is reinforced, according to plasticmoulds.net. That figure reflects the demand for stiffness and heat resistance. The neat grade still wins where chemical purity or dielectric strength matters. Teams should read this comparison with pure pps as a starting point, then test the actual part. The mechanical properties of each grade depend on fiber content and processing, so the table offers guidance rather than a final answer.


Unfilled PPS suits toughness-critical, smooth-surface, cost-sensitive parts. A glass fiber reinforced pps sheet suits stiffness-critical, high-heat, dimensionally tight parts. Teams should match the pps grade to the dominant demand of the application. Defaulting to one material ignores the real service conditions.

FAQ

Which grade should a designer choose for a part facing both heat and impact?

Heat wins the first filter. A part above 150°C under load needs the glass fiber reinforced pps sheet. Below that threshold, impact demands favor the unfilled grade.

Does the glass-filled grade always cost more per part?

Not always. The filled compound costs less per kilogram. Its higher stiffness allows thinner walls, so cost per finished part can favor either grade.

Can unfilled PPS handle structural brackets?

Rarely. Unfilled pps creeps under sustained load and softens near 135°C. Structural brackets need the creep resistance and stiffness of the reinforced grade.

Previous page

Next page

Previous page

Next page

Relevant information


Future Trends: PA66 Glass Fiber Reinforced Electrical Grade in Sustainable Buildings

Future Trends: PA66 Glass Fiber Reinforced Electrical Grade in Sustainable Buildings Table of Contents 1. Introduction to Sustainable Building Materials 2. What is PA66 Glass Fiber Reinforced Electrical Grade? 3. Advantages of PA66 in Construction 4. Applications of PA66 in Sustainable Buildings 5. Environmental Impact of Using PA66 6. Future Trends in PA66 Usage 7. Ch

Learn more